Access Point Cisco WAP4410N Access Point Wireless-N PoE [ WAP4410N ] - Xtech Informática

Caracteristicas Gerais

Padrão IEEE 802.11b/g/n (802.3, 802.3u/af, 802.1x) Ganho Antena: 2dBi Portas 1 RJ45 10/100Mbps (LAN), 1 Power Segurança WEP (64/128) bits, WPA, WPA2 Gerenciamento Web, SNMP (v1,v2c) Leds Power, Ethernet, Wireless, PoE Garantia 36 meses Specifications: Standards Draft IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af (Power over Ethernet), 802.1x (security authentication), 802.11i security WPA/WPA2, WMM Ports Ethernet, Power Buttons Reset Cabling type Unshielded twisted pair (UTP) Category 5e or higher LEDs Power, Ethernet, Wireless, PoE Operating system Linux Setup/Configuration Web user interface Built-in web user interface for easy browser-based configuration (HTTP/HTTPS) Management Simple Network Management Protocol (SNMP) version SNMP version 1, 2c Event logging Event logging Email logging Remote syslog Web firmware upgrade Firmware upgradeable through web browser Diagnostics. Flash, RAM, LAN, WLAN Dynamic Host Configuration Protocol (DHCP) DHCP client HTTP Redirect Redirects initial user access to an external web server to display company logo or network usage policy IPv6 host Support for management and control of access point over IPv6 Supports RFC2460 (IPv6 protocol) and RFC4294 (IPv6 node requirements) Network Capabilities Multiple BSSID Supports up to 4 BSSIDs, allowing the creation of multiple virtual access points VLANs Supports 802.1q - up to 4 VLANs SSID to VLAN mapping Supports mapping of SSIDs to VLANs to securely separate workgroups across wireless and wired domains Spanning Tree Supports 802.1d Spanning Tree Protocol to prevent loops when using wireless distribution system (WDS) links as redundant links in a distribution system Operating modes Access point mode, point-to-point bridge mode, point-to-multipoint bridge mode, repeater mode, wireless client mode Load balancing Allows bandwidth control with user-defined CPU usage ratios Auto-channel selection On boot-up, the access point selects the least congested channel 802.11d regulatory domain Enables the access point to provide radio channel settings for client devices, facilitating easy client access as they move across regulatory domains Security WEP/WPA/WPA2 Wired Equivalent Privacy (WEP) 64-bit/128-bit, WPA-Pre-Shared Key (WPA-PSK), WPA2- PSK, WPA-ENT, WPA2-ENT Access control Wireless connection control: MAC-based SSID broadcast SSID broadcast enable/disable Client isolation Supports wireless client isolation between and within SSIDs 802.1X Wireless clients can be authenticated through IEEE 802.1X 802.1X supplicant Supports 802.1X supplicant on the Ethernet port to allow the access point to authenticate itself to the network RADIUS server Up to 2 RADIUS servers can be configured for redundancy purposes WPS Supports WPS, a WI-FI Alliance specification for simple and secure setup of a wireless network Rogue access point detection New access points detected that have not been categorized as known are logged as rogue access points, allowing the administrator to clamp down on unapproved devices in the network Quality of Service QoS 4 queues 802.1p VLAN priority WMM wireless priority Mapping of 802.1p VLAN priority to WMM wireless priority to maintain end-to-end QoS Wireless Spec/modulation Radio and modulation type: 802.11b/DSSS, 802.11g/OFDM, 802.11n/OFDM Channels Operating channels: 11 North America, 13 most of Europe (ETSI and Japan) Internal antennas None External antennas 3 (omnidirectional) Transmit power Transmit power @ normal temp range for FCC: 802.11b: 16 dBm @ 1TX, 19 dBm @ 2TX, 20.5 dBm @ 3TX 802.11g: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX 802.11n: 17 dBm @ 1TX @ MCS0~5/8~13, 13 dBm @ 1TX @ MCS6/14, 11 dBm @ 1TX @ MCS7/15, 20 dBm @ 2TX@MCS0~5/8~13, 16 dBm @ 2TX @ MCS6/14, 14 dBm @ 2TX @ MCS7/15, 21.5 dBm @ 3TX@MCS0~5/8~13, 17.5 dBm @ 3TX @ MCS6/14, 15.5 dBm @ 3TX @ MCS7/15 Transmit power @ normal temp range for ETSI: 11b/g/n: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX Antenna gain in dBi 2 Receiver sensitivity 802.11.n: 300 Mbps at -69dBm 802.11.g: 54 Mbps at -73dBm 802.11.b: 11 Mbps at -88dBm Environmental Dimensions 6.69 x 6.69 x 1.60 in. W x H x D (170 x 170 x 40.7 mm) Weight 0.86 lb (39 kg) Power 12V 1A DC input, and IEEE 802.3af compliant PoE Max power draw: 10.1W Certification FCC, CE, IC Operating temperature 32 to 104F (0 to 40C) Storage temperature -4 to 158F (-20 to 70C) Operating humidity 10% to 85%, noncondensing Storage humidity 5% to 90%, noncondensing Package Contents Cisco WAP4410N Wireless-N Access Point with PoE User guide on CD-ROM Ethernet network cable Power adapter Product stands Registration card Minimum Requirements 802.11b, 802.11g, 802.11n wireless adapter with TCP/IP protocol installed per PC Switch/router with PoE support or PoE injector when used with PoE Web-based configuration: Java-enabled web browser Especificacoes: